Manuals

Instructions EMS PRO

Congratulations on choosing your eaglefit PRO EMS System. This high-quality electrical muscle stimulation training device was developed with extensive expertise and knowledge so you can perform highly efficient EMS fitness training at home or on the go with minimal effort.

About these instructions

EMS devices have been used in physiotherapy and competitive sports for many years. By observing the safety instructions and warnings, you can use this device to perform targeted training at home or on the go, in a hotel or at the office.

To get the greatest possible benefit and, above all, to eliminate dangers and risks, please be sure to read these instructions and follow the rules of conduct described.

We hope you enjoy your eaglefit PRO EMS System.

Safety instructions

Intended use

The eaglefit PRO EMS System is a training system based on highly efficient electrical muscle stimulation (EMS) and developed for private use. By combining the PRO Box and the eaglefit EMS System app, you can perform an EMS workout at home, in the office, or on the go at any time. This instruction manual will guide you step by step through the training and operation, and provide you with valuable tips and advice for EMS training.

The eaglefit PRO EMS System is exclusively a training and fitness device, not a medical product.

If you have any doubts about your health, seek medical advice before starting. This list does not replace an individual medical assessment.

Safety notice

People with heart problems or other cardiovascular diseases, electrical implants, metabolic disorders (e.g. type I or II diabetes, diseases of the thyroid, liver or kidneys), cancer, an abdominal wall or inguinal hernia, those who are pregnant or undergoing chemotherapy must NOT do this workout! We recommend EMS training only for people aged 18 and over.

You can find our product safety data sheet here: to the safety data sheet

Improper use

Read the operating instructions and all information and notes carefully to prevent personal injury and property damage and to avoid dangerous situations. If the instructions and information on proper handling are not followed, eaglefit GmbH accepts no liability for any resulting personal injury or property damage. In such cases, the warranty is also void.

Before use, please check your eaglefit PRO EMS System for damage and contact the manufacturer or your dealer immediately if you notice anything unusual.

Training with the eaglefit PRO EMS System must only be carried out in a dry environment. Avoid environments with very high humidity and those where you could come into contact with water (e.g., in the rain, near bathtubs, etc.).

Risks and contraindications

Although no cardiac arrhythmias have ever occurred during training with an eaglefit PRO EMS System, legislation requires that users be warned about the residual risk. If you have a pre-existing cardiac arrhythmia, training with the eaglefit PRO EMS System is not recommended, as it may otherwise pose a risk to life.

Absolute contraindications

  • Acute illnesses, bacterial infections, or inflammatory processes
  • Recent surgery (< 2 months)
  • Arteriosclerosis, arterial circulatory disorders
  • Stents or bypass grafts that have been in place for less than 6 months
  • Untreated high blood pressure
  • Diabetes mellitus
  • Pregnancy
  • Electrical implants, e.g. pacemakers
  • Tumors or cancer
  • Bleeding disorders, tendency to bleed (hemophilia)
  • Neurological diseases, epilepsy, or multiple sclerosis
  • Abdominal wall or inguinal hernias
  • Cardiac arrhythmias

Relative contraindications

  • Acute back pain without a diagnosis
  • Acute neuralgia, herniated discs
  • Implants (prostheses)
  • Diseases of the internal organs (especially the kidneys)
  • Cardiovascular diseases
  • Motion sickness
  • Significant fluid accumulation in the body, edema
  • Open skin injuries, wounds, eczema, burns
  • Varicosis, varicose veins
  • Acute effects of alcohol, drugs, or intoxicating substances
  • Vaccination

If you have one absolute contraindication or several relative contraindications, you must not use the eaglefit PRO EMS system. Training despite existing contraindications can result in anything from minor injuries to death. We expressly point out that you must not train if you have any of the contraindications listed.

If in doubt, talk to your doctor before use to find out whether EMS training is suitable for you.

Electrical hazards

If you find any damage to any of the components, do not use the eaglefit PRO EMS system. Handle it with exceptional care to prevent damage to the material or cables. This means:

  • Never use the eaglefit PRO EMS system in wet environments
  • Do not pinch or kink the cables, and do not place heavy objects on them
  • Remove all piercings or similar items from the training area before your workout

Damage must be reported to the manufacturer, who will then decide what action to take.

No specific medical and/or physiological knowledge is required to train with the eaglefit PRO EMS System. However, before your first training session with the eaglefit PRO EMS System, you must read and understand the instruction manual carefully. Failure to observe the information provided in this instruction manual can lead to dangerous situations and, in extreme cases, death. The manufacturer accepts no liability for any resulting damage in the event of non-compliance.

Meaning and Function

Training with electrical muscle stimulation (electromyostimulation), also known as EMS training, is based on the targeted stimulation of striated muscles using electrical impulses. This simulates natural muscle activation. This activation causes the muscle fibers to contract without receiving a signal from the central nervous system (CNS). Normally, the commands for a contraction come from the brain. During physical exertion, these electrical impulses are sent to the muscles via nerves. Because the impulses used in EMS training are so similar to those of the CNS, the muscle cannot distinguish their origin, resulting in a contraction; that is, the contraction command reaches the muscle via the electrodes integrated into the eaglefit PRO EMS Suit. During EMS training, rhythmic stimuli or impulses act on the muscles being trained, causing them to tense and relax in a targeted manner. In physiotherapy, electrical stimuli are usually used to train individual muscles or muscle groups without performing additional movements or fitness exercises.

While no movements are performed alongside electrical muscle stimulation, full-body EMS training involves targeted exercises. This also trains your coordination, and the increase in strength can be applied to specific movements. In addition, full-body training strengthens the agonists, antagonists, and stabilizing muscles, which are difficult to target and influence with conventional training. This helps prevent muscular imbalances, which can occur when training individual large muscle groups in isolation.

Simultaneous muscle activation can also prevent or correct protective postures, helping to avoid improper strain. The option to incorporate additional exercises during EMS training can improve intra- and intermuscular coordination as well as motor skills. Another positive effect of the additional exercises is that the tendons, ligaments, and joints adapt to the increased muscle strength achieved. Since heavy weights are not needed to contract the muscles, this form of full-body training is very gentle on the joints.

Another advantage is the time saved compared with conventional forms of training:

  • Only 20-60 minutes of training per week is enough

Possible positive effects of EMS training

  • Reduced waist and abdominal circumference
  • Reduced body fat
  • Increased endurance and performance
  • Back pain may be reduced
  • Improved endurance when putting strain on the back in everyday situations
  • 15-20 minutes of EMS training burns approximately 400-500 kcal with appropriate intensity and exercise execution
  • Increased maximum performance (movement speed + strength)

Possible specific effects of EMS training

EMS and exercise

  • Unlike static activity, dynamic muscle work improves blood flow and lymphatic circulation
  • Physical activity improves tendon tensile strength and nourishment of joint cartilage
  • Tendons, ligaments, and joint cartilage are strengthened, and bone mineral content and size increase
  • Eccentric strength training in particular affects connective tissue (tendons and ligaments)
  • Tendon and ligament injuries can heal faster with targeted activity
  • These changes make the body more resilient and protect it from injury

EMS and functional training

  • Full-body training (muscles, tendons, ligaments)
  • The focus is on learning and performing the movement
  • Based on stabilizing the body, especially the core muscles
  • Can be supplemented with various training equipment (e.g., Sling trainer, balance pad, kettlebell, exercise ball)

EMS and sling training

  • Full-body exercises and isolation exercises for individual muscles
  • Exercise intensity can easily be varied by changing the angle relative to the Sling trainer’s anchor point
  • Trains stabilizer muscles using unstable grip cords, with the pulley making the workout even more intense
  • Wide range of exercises thanks to the pulley
  • Requires little space
  • Easy setup and takedown

EMS and outdoor training

  • The focus is on training and outdoor exercise
  • Full-body exercises
  • Exercise intensity varies with body weight, terrain, or everyday objects
  • Psychological benefits of outdoor training
  • Motivation through variety

Full-body EMS training offers the opportunity to train highly effectively and efficiently. It is therefore an excellent way to increase strength, build muscle, and reduce fat. It allows you to generate stimulus intensities that are higher than those achieved with conventional training methods.

For these reasons, several important conditions must be observed during training.

Training preparation

  • Full-body EMS training can only be performed when you are in an appropriate physical condition
  • Be sure to replenish your carbohydrate stores before training, as the very large muscle mass engaged results in a high metabolic load
  • You should also make sure to increase your fluid intake before, during, and after training

Training progression

  • During your first training sessions, you should never overexert yourself. Training should be done for a shorter duration (approx. 12-15 min.) and at an appropriate intensity. After that, gradually increase the training time to 20 min.
  • For the first 8-10 weeks, allow at least 4 days between training sessions. This is the only way to ensure recovery and positive adaptation

Quick start guide

Quick start guide for your new eaglefit PRO EMS System

  1. PRO Box charge until the LED lights up green
  2. eagle fit EMS System App in the App Store download
  3. Suit put on – if your skin is extremely dry or you have heavy body hair, dampen the electrodes slightly or use electrode spray
  4. Turn on the PRO Box (press lightly with your index finger into the small indentation between the logo and the LED for 2 seconds), attach it to the Suit, launch the app
  5. Assign a new profile name for the upcoming training session
  6. Establish a Bluetooth connection to the PRO Box (click “Bluetooth” in the top right, then “Scan,” then “Connect”)
  7. Under “Parameters,” adjust the settings for the profile, warm up sufficiently, then press “Start”
  8. Increase the intensity of the muscles one by one using the exclusion method (press the up arrow until the intensity is high enough, tap the number above the muscle so that it is outlined in gray)
  9. Start training, end after 20 minutes
  10. Save settings by exiting the app using the arrow in the top left
  11. Make sure to drink enough water before, during and after training, at least 1/2 liter more than usual
  12. Leave at least 48 hours between workouts (for the first 10 weeks, no more than 1 workout per week)

You can also watch our detailed onboarding video: EMS onboarding

Tips for use

Switch the PRO Box on/off correctly:

  • To switch on, press for 2 seconds gently with your index finger into the recess between the logo and the LED
  • To switch off, press for 6 seconds gently with your index finger into the recess between the logo and the LED

We deliberately set the time required to switch off the box to 6 seconds so you don't accidentally touch the box during your workout and turn it off unintentionally.

Tips for use – EMS PRO
Tips for use

First use of the PRO Box and the app

Charging the PRO Box

Before you can start training, please download and install the eaglefit EMS System App from your app store by searching for “eaglefit” or “eaglefit EMS System”.

Before using the PRO Box for the first time, you must charge its battery for at least 3 hours. Our batteries have overcharge protection, so you cannot “overcharge” them. Use the supplied USB cable and the 220 V power adapter to charge it. While charging, the indicator on the PRO Box glows blue. When the battery is fully charged, the indicator glows green.

Download the eaglefit EMS System App from your app store:

First launch

When you start the app, you can first choose between the different boxes (BELT, HOME, PRO or CONNECT). Then select the relevant product.

If this is your first time using the app, create a profile for your training. Later, you can save all your settings under “Select profile.”

Charging the PRO Box – EMS PRO
Charging the PRO Box
Charging the PRO Box – EMS PRO
Charging the PRO Box

If you have already created a profile, it will be displayed. Select a saved profile or add a new one, where you can save your settings (impulse intensity for each muscle, etc.) as you go.

The app is designed to always save the most recently set values for a training program in the profile. Therefore, the app overwrites your settings as soon as you switch training programs within a profile.

We recommend creating a separate profile for each training program so you can always set and access the correct values for each program.

Once you have selected a profile, press “Confirm” to go to the training interface with the preset values of the profile highlighted in green. Your changes will be saved if you leave this page later using the green “return arrow” button.

First, please establish the Bluetooth connection to the PRO Box. Switch on the charged PRO Box (place one finger on the indentation for about 2 seconds) and search for it in the eaglefit app via “Bluetooth” in the top right next to the battery indicator, by tapping “SCAN” in the next window. Select your PRO Box (e.g. “eagle_pro000”) by tapping “Connect” at the end of the row. You will then return to the training interface.

In the training interface, you can adjust the intensity of each pair of electrodes, switch electrodes on/off, and use the green menu icon (bottom left, with the three lines) to access the parameter menu.

App overview

The app is designed to let you create as many profiles as you like on each device. A profile stores all settings and parameters for one impulse type (Fitness / Metabolism / Relaxation / Custom / Fat Burning / HIIT / Mobility / Speed Strength). Assign each profile an appropriate name.

The name could be “Thomas_Fitness” or “Muscle Building,” for example. In accordance with the GDPR, your data is stored exclusively on your device. Therefore, you need to create separate profiles on your iPhone and iPad, for example.

Establishing the Bluetooth connection

Communication between the app and your PRO Box will be established once a Bluetooth connection is made.

To establish the Bluetooth connection, tap “bluetooth” in the top right, next to the battery indicator, the first time you use it.

In the following view, select “Search” to find all available Bluetooth devices.

You will see a list of available Bluetooth devices nearby.

Please select “eagle_pro000” to connect to the PRO Box.

Establishing the Bluetooth connection – EMS PRO
Establishing the Bluetooth connection
Establishing the Bluetooth connection – EMS PRO
Establishing the Bluetooth connection

Requirements for a Bluetooth connection

  • The PRO Box must be charged and switched on. You can tell by the bright glow of the green/blue LED.
  • Turn on the PRO Box by pressing the button (a slight recess in the middle) for 2 seconds. The LED will turn on and glow blue
  • To switch it off, press the button for approximately 6 seconds
  • You must allow the app to access your location so that the Bluetooth signal can be processed correctly
  • You will NOT find the PRO Box in your usual Bluetooth settings on your phone, as we use Bluetooth Low Energy (BLE)

Navigation and settings for EMS impulses

Navigation and settings for EMS impulses – EMS PRO
Navigation and settings for EMS impulses
  1. Program selection
  2. Reset - sets all intensities to "ZERO"
  3. Select/deselect all intensities for each muscle group
  4. Increase all activated intensities for each muscle group
  5. Decrease all activated intensities for each muscle group
  6. Start/Pause - Start or pause your training
  7. Activate/deactivate muscle groups by tapping the muscle group name
  8. Bluetooth menu - tap here to connect the HOME EMS Box
  9. Active training time
  10. The green dots show which electrodes are actually activated
  11. auto: Pressing this switch starts your training at an intensity of "0" and linearly increases the intensities over 2 minutes, up to 80% of the preset values. You must adjust the remaining 20% manually
  12. Sound on/Sound off: Here you can set signal tones to indicate when an active impulse phase is underway and when there is a pause

Settings under “Parameters”

The parameters already have default settings configured. Click + or – to adjust the parameters highlighted in black.

The following programs (“modes”) are preinstalled in the eaglefit EMS System App:

Fitness

Please select the “4/2” setting, meaning a pulse duration of 4 seconds and a 2-second pause. Ideally, tense your muscles for 4 seconds during training and relax them for 2 seconds.

The fitness program is ideal for building large-volume white skeletal muscle. It increases your maximum strength and promotes muscle growth. White skeletal muscle is trained best with 6-8 repetitions per muscle group at around 80% of your maximum strength. The impulses are delivered to each muscle group at a frequency of 85 Hz without placing stress on your joints, ligaments, or tendons with heavy training weights. The pulse width in this program is 350 µs.

Fitness training should be combined with exercises and can be supplemented effectively with, for example, sling training or HIIT.

Recommended training:

  • Strength/weight training
  • few repetitions (6-8)
  • 1 set per muscle group

Metabolism/cardio

Please select a pause time of 0 seconds for continuous pulses. The pulse duration setting does not matter in this case.

The metabolic program, which trains the red endurance muscles, can be used specifically for muscle toning. It is our classic endurance/athletic program. Activating slow-twitch muscle tissue burns fat and increases muscle definition. The training frequency is 7 Hz with a pulse depth of 350 µs.

This program is ideal for warming up and improving blood circulation and metabolism. Ideally, metabolic training should be combined with endurance exercises such as:

  • Nordic walking
  • Jogging
  • Cycling
  • Exercises on cardio machines
  • Yoga
  • Static exercises (do not set the intensity too high)

Relaxation

Please select the “1/1” setting, i.e. a pulse duration and a pause of 1 second each.

This program produces gentle muscle twitches and promotes muscle relaxation, faster recovery and is also used for functional rehabilitation after illness. At a training frequency of 100 Hz and a pulse depth of 150 µs, muscle tension is relieved and the muscles are supplied with nutrients.

You can use the relaxation program for 5-10 minutes after an intense workout (with or without EMS), or for 10-30 minutes at a moderate intensity after a demanding day, for example, while relaxing on the sofa.

Choose a low intensity here - the pulse should create a pleasant, massaging sensation.

Individual

Choose the settings based on your individual preferences or therapeutic recommendations.

Advanced users can freely adjust all parameters in this program (pulse frequency, pulse depth, pulse duration, pause, and training duration). Frequencies of 1-120 Hz and pulse depths of 50 – 400 µs are available.

Deep Core for deep muscles close to the spine

This training program is specifically designed to gently but effectively strengthen the deep muscles close to the spine. The aim is to activate the deep stabilizing muscles in the back to relieve pressure on the intervertebral discs and support the spine in the long term.

How it works:

The program creates a steady alternation between muscle tension and relaxation. The moderate impulses at 27 Hz primarily improve muscular endurance and stability. The comparatively long pulse duration provides an intensive yet gentle workout, while the short breaks support steady blood circulation and recovery.

Area of use:

  • Support for back pain associated with disc problems
  • Strengthens the deep core muscles
  • Helps prevent poor posture and muscular imbalances
  • Suitable for beginners as well as people undergoing rehabilitation

Video training

In this program, you can watch an avatar demonstrate training exercises and put together a short training plan from a selection of ready-made exercises. The special feature is that you can choose a different frequency and pulse depth for each workout. Simply hold your finger over the desired exercise for 2-3 seconds until the preview image lifts up, then drag it to the row below and arrange it. You can remove exercises from the row in the same way.

Fat burning

Please select the “4 / 2” setting, i.e. a pulse duration of 4 seconds and a “pause” of 2 seconds. In this special program, you combine the benefits of the fitness and metabolic programs. During the active phase, you train at 60 Hz for maximum strength, and during the passive phase (pause phase), your endurance muscles are engaged at 7 Hz. This way, both muscle fiber types are alternately challenged in one program.

Explosive strength

Use this program for muscle building. The special feature is that 100% of the set impulse intensity is delivered from the first second (ramp=0). This setting is especially effective for athletes with explosive movements (for example, golf), ball sports, or reactive sports.

Mobility

The app setting in the eaglefit PRO EMS app for mobility training is based on a special EMS program designed specifically to support muscle length and mobility training (mobility). The training is designed for gentle muscle stimulation to improve flexibility, range of motion and neuromuscular coordination without placing excessive strain on the muscles.

Characteristics of the app setting for mobility training:

  • High frequency (120 Hz): This supports gentle muscle activation without strong contractions and is ideal for continuous movements and stretching exercises.
  • Long pulse duration (350 µs): This reaches deep into the muscles, which is particularly beneficial for muscle length training and mobility exercises.
  • Gentle impulse intensity: The intensity can be adjusted individually and is selected to create a noticeable but comfortable muscle contraction – ideal for supporting mobilization without pain or exhaustion.
  • Dynamic impulse patterns (anterior and posterior chains): You can choose to activate either the anterior or posterior chain with just one click. This automatically helps you feel and activate the right muscles.
  • Interval duration: With the preset, you activate the selected muscle chain for 30 seconds at a time and can move into the other position during the 15-second break.

Purpose of the setting:

EMS support during mobility exercises helps loosen tense muscles, improve mobility and, thanks to the additional neuromuscular activation, also increase the effectiveness of your workout – especially when combined with targeted stretching and mobility exercises.

Pulse depth

“Pulse depth” lets you set how long the impulse you set under “Frequency” lasts. This value can only be configured in the “Individual” parameter. A single electrical impulse can last 50-400 µs.

The higher this value is set, the deeper the impulse penetrates the muscle. For example, you can optimally target large muscles such as the thigh muscles, glutes or back muscles with a pulse depth of 350 µs.

Pulse duration

Duration of the impulse in seconds, adjustable from 1-40 seconds (shown as a green number counting down during training).

Break

The length of the break during training, 0-40 seconds (shown as a red number counting down).

Training

For most training programs, we recommend a duration of approximately 20 minutes per session.

Frequency

The number of impulses per second. For example, during the “Fitness” training program, the muscles contract and relax 85 times per second.

Putting on and taking off

The eaglefit PRO EMS Suit is available in sizes 3XS to 4XL. It is important to choose a close-fitting size so that the electrodes sit snugly against your body. The suit can be used as either a dry suit or a wet suit. When used as a dry suit, it is worn directly against bare skin, without underwear or other (sports) clothing. The electrodes do not need to be wetted; they should be placed directly over the muscles to be stimulated. Close contact with the skin ensures optimal transmission of the current to the muscle.

For the dry suit’s electrodes to transmit energy through your skin to your nerves and muscles, a very thin film of moisture is needed. For some skin types, simply wearing the suit for 2-3 minutes is enough. Other skin types need to warm up for 5 minutes by doing jumping jacks, burpees or sit-ups before the intensity of the impulses can be increased. If there is no moisture film, you may feel an unpleasant, slight stinging on the surface of your skin. If this happens, reduce the impulse intensity for that muscle group and do a few more jumping jacks or squats before increasing the intensity. Heavy body hair or very dry skin can impair stimulation. In this case, you can lightly dampen the skin in the relevant areas with a cloth or use our electrode spray.

The eaglefit PRO EMS Suit is fastened with the zipper at the back. Simply use the attached cord to close the zipper while pulling the bottom of the zipper in the opposite direction with your other hand. This tightens the zipper so you can easily pull it up using the cord. At the bottom, there is a small, square fabric patch attached to the Suit with a hook-and-loop fastener. You can remove it, lay the zipper cord over the hook-and-loop fastener, and reattach the fabric patch. This keeps the cord from swinging around during training. If the Suit does not fit snugly in some places, you can purchase hook-and-loop straps for the arms and legs in our shop or use the included hip belt for the lower back to press the Suit against the skin in those areas too. Alternatively, you can wear close-fitting clothing over the eaglefit PRO EMS Suit to achieve the same effect.

After training, open the zipper and roll the eaglefit PRO EMS Suit inside out to take it off. Then wash the Suit according to the washing instructions or hang it on a clothes hanger.

Training/Exercises

As a general rule: If you feel unwell, stop training immediately and consult a doctor if necessary. Never work out if you are not feeling well or are ill.

Training must also be stopped in the event of problems or malfunctions with the eaglefit PRO EMS system. In the event of technical malfunctions, contact the manufacturer.

1. Warm-up

Before an EMS workout, the muscles should be prepared for the upcoming exertion, just as before any fitness workout. Warming up has the following effects:

  • Conductivity between the electrodes and skin increases with light sweating
  • Increased core body temperature
  • Improved energy supply processes in the muscles
  • Increased production of synovial fluid
  • Increased motivation and focus on the upcoming workout

For warming up, we recommend a short endurance session, such as a few jumping jacks, burpees, or 3-5 minutes on a stationary bike.

You can already set and activate weak impulses here.

2. Training/Exercises

In general, with the eaglefit PRO EMS Suit, you can do any movements and workouts indoors or outdoors in dry weather. There are no limits to your imagination. Jogging, boxing, yoga, sling training, functional training, HIIT, or bodyweight training. The only thing to avoid is wet conditions (e.g. rain) while wearing the Suit.

The eaglefit PRO EMS Suit comes with an exercise poster featuring exercises for the whole body using your own body weight.

3. Stretching

After your workout, you should stretch for 2-3 minutes – optionally combined with the “Relaxation” program.

Stretching has the following effects:

  • Reduced muscle tone
  • Improved removal of metabolic waste products
  • Improved muscle recovery
  • Improved mobility

Washing and hygiene instructions

Before washing the eaglefit PRO EMS Suit, please remove the PRO Box.

Proceed as follows:

1. Open the hook-and-loop fastener

1. Open the hook-and-loop fastener – EMS PRO
1. Open the hook-and-loop fastener

2. Pull the Box upward

2. Pull the Box upward – EMS PRO
2. Pull the Box upward

3. Remove the Box

3. Remove the Box – EMS PRO
3. Remove the Box

Please clean the PRO EMS Box with a soft cloth only.

We recommend hand-washing the eaglefit PRO EMS Suit. Alternatively, you can wash the Suit in a laundry bag in the washing machine on a delicate cycle at 30 °C. Before washing, please remove the Box and be sure to close the zipper and all hook-and-loop fasteners.

We recommend using the Lavendelkraft detergent. Be sure never to use corrosive solvents or abrasive cleaners, sports detergents, disinfectants, water softeners such as Calgon, or detergents containing additives such as chlorine or bleach. If the Suit is still too wet after washing, you can spin it at a maximum of 900 rpm. To dry the Suit, simply hang it on a clothes hanger and let it air-dry – preferably with the electrode pairs facing outward. Never dry the eaglefit PRO EMS Suit in a tumble dryer, and never expose it to direct UV radiation. This can damage the material.

The following washing symbols can be found on the eaglefit PRO EMS Suit and should be observed:

3. Remove the Box – EMS PRO
3. Remove the Box

Disposal and recycling

The eaglefit PRO EMS Suit and the PRO Box contain electrical components. Electronic devices are recyclable materials and do not belong in household waste. At the end of its service life, dispose of the product in accordance with the applicable legal regulations. By doing so, you fulfill your legal obligations and contribute to environmental protection.

There are collection points for recycling electrical and electronic devices in all countries of the European Union. You can obtain information about these collection points from your local waste disposal authority.

Outside the European Union, please follow your country's specific disposal regulations.

Information on the safe removal of batteries or rechargeable batteries:

To dispose of the PRO Box, you can remove the battery by unscrewing the 4 Phillips screws on the back beneath the film and unplugging the battery.

  • Warning: Make sure the battery is completely discharged
  • Carefully remove the battery or rechargeable battery
  • The battery or rechargeable battery and the device can now be disposed of separately

Battery type: LiPo; 3.7 V, 3,000 mAh. Chemical system: Lithium-polymer battery

Disposal and recycling – EMS PRO
Disposal and recycling

Technical specifications

PRO Box Value
Bluetooth version > 4.0
Power supply 5 V, USB C
Battery 3.7 V; 3,000 mAh LiPo

Warranty

You receive a 2-year warranty against material and workmanship defects. The warranty is valid in all countries where the eaglefit PRO EMS System is officially sold. The warranty does not cover damage caused by improper or negligent handling.

If you think that individual electrodes have stopped working, you can check as follows:

  • Make sure the muscle group is activated in the app (the muscle name is highlighted in green)
  • Switch on the PRO Box, attach it to the Suit, and turn it inside out
  • Connect the PRO Box in the app and select the “Metabolism” program
  • Set the impulses for the affected muscle group to intensity 20
  • Moisten the electrodes of the affected muscle group with a damp cloth
  • Now place your left hand on the left chest electrode, for example, and your right hand on the right chest electrode

Since the current flows through our electrodes from one side to the other, it is important to place both hands on one electrode each of the affected muscle group to close the circuit.

If you now feel a tingling sensation in your hands, the electrode pair is intact.

EU Declaration of Conformity

EU Declaration of Conformity – EMS PRO
EU Declaration of Conformity

Manufacturer information

The eaglefit GmbH is permitted to affix the CE marking to the eaglefit PRO EMS System, thereby demonstrating conformity with relevant EU directives.

Contact

Cart